SmartHealth Smartwatch Quick Start Guide and App Installation Instruction

Quick Start Guide

Description

• Full Touch Screen: swipe in four directions (left, right, top, and bottom).
• Display Area.
• Bluetooth Connection Status.
• Side Button (Back to Home Menu).
• Back Electrode L.
• Back Electrode R.
• ECG Electrode.
• Heart Rate Sensor.
• TPU Watch Strap (20mm Width).
• Magnet Pogo Pin USB Charging Port.

Note: When testing ECG (Electrocardiogram), you need to fully contact the three electrodes with the skin, your finger needs to keep touch with the metal part on the side of the watch.

Instruction for Charging

• For initial use, please charge the smartwatch.
• You can use the USB cable to charge the watch. One side of the cable connects to the watch, and the other side of the cable is for standard USB Port. The watch can be charged by any USB power adapter or USB port on your PC.
• If the watch cannot be charged by the USB cable, please clean the connections part on the watch and the pin on the USB cable. During the charging, the battery icon will be shown on the screen.
• Charging by USB port on PC, laptop, or power bank.
• Charging on USB power adapter.

Note: There is no power adapter inside the standard package.

Install the App SmartHealth

• You can search the App name SmartHealth from Google Play store or iOS App store.
• You also can scan the QR code to get the download link.

Troubleshooting

• You cannot connect the smartwatch to your smartphone. You can try to turn off the Bluetooth on your phone settings. Wait for several minutes and turn on the Bluetooth. Open the App and search for the smartwatch again.
• The smartwatch is continuously disconnected from the smartphone. It is not the smartwatch problem, it is a setting problem with the App on a smartphone. You must give enough permission for the App to running on the smartphone background. Otherwise, most smartphones will turn off the App on the background for power saving.
• The measurement results of the watch are for reference only. You need to let the watch measure your data for some days, and then you will have an average value. You can refer the average data from the watch. Do not compare the value only with other devices, which makes no sense.

App Installation Instruction

1. Go to "Google Play Store" or "Apple Store".
2. Search "SmartHealth" on the APP Store on your Smartphone.
3. Find the APP "SmartHealth" as below picture.
4. Install the APP "SmartHealth".
5. Open the "SmartHealth" after the installation finished.
6. Tap Watch icon to add the Watch to the APP.

1. Select "Allow all the time".
2. Get location info "Always allow".
3. Register the APP with your smart cell phone number or E-Mail. The verification code will send to your SMS or E-Mail. You also can use the APP without registration.
4. If you click "Skip", you will see the interface. Select "Allow all the time".
5. Click "I get it".
6. Lower right corner, select "Settings", and then click "Connected".

1. "Connected" is search "Smart bracelet" device. If you cannot see your smart bracelet E66+**, please click the "refresh" on top right corner.
2. Then it will appear your Smart bracelet ID (ex E66+4076). Click the E66+4076, and connect. If cannot see any smart bracelet ID, please check whether you open your "bluetooth".
3. After you connect the bracelet, you can see this interface. And you can click the "E66+4076". Here you can set a lot of data about the bracelet.
4. Click the "Notification", click "notification on".
5. Click the "notification" first time, will appear this interface, please tap "SmartHealth" and set it ON. There will appear a selection, please select "Allow".
6. Click the "notification" again, will appear this interface, you can choose which APP you want to receive the notification. Set it ON or OFF.

SMS and Calls Reminder Settings on Android

If the Smart Watch cannot get SMS and Calls reminder from your Smart Phone, please check the following settings on your Android Smart Phone.

1. Find Settings on your smart phone.
2. Find the APPs on your Smart Phone Settings.
3. Tap on Permissions.
4. Find the SmartHealth and tap on it.
5. Important: Check all settings as attached picture. Make sure the settings are turned ON.
6. Go to App SmartHealth. And Turn off the Notifications, then Turn on Notifications, and keep the Notifications Turns ON.